[2017 New Cisco Version] Prepare for New CCNA Cyber Ops 210-250 Dumps SECFND PDF Questions And Answers for Cisco CCNA Video Series Will Be More Popular (From Google Drive)

Posted by on

Are you want To Pass Cisco 210-250 dumps in the first attempt? Pass4itsure prepare for new CCNA Cyber Ops 210-250 dumps SECFND pdf questions and answers for Cisco CCNA video series will be more popular.”Understanding Cisco Cybersecurity Fundamentals” is the 210-250 exam dumps which covers all the knowledge points of the real Cisco exam. Pass4itsure 200-105 dumps exam questions answers are updated (80 Q&As) are verified by experts. The recommended course syllabuses have been carefully examined in order to create the Cisco https://www.pass4itsure.com/210-250.html dumps tests.  Pass4itsure use material that guarantees you to learn the exact information that will be on your exam.

Exam Code: 210-250
Exam Name: Understanding Cisco Cybersecurity Fundamentals
Updated: Sep 04, 2017
Q&As: 80

[2017 New Version Cisco 210-250 Dumps From Google Drive]:https://drive.google.com/open?id=0BwxjZr-ZDwwWRzdFOXJORHhsck0

[2017 New Version Microsoft 70-734 Dumps From Google Drive]:https://drive.google.com/open?id=0BwxjZr-ZDwwWY2xEbzRCZklmTFU

Major Cisco 210-250 dumps topics include:

  • Networking Concepts
  • Security Concepts
  • Cryptography
  • Host-Based Analysis
  • Security Monitoring
  • Attack Methods
  • Endpoint Threat Analysis and Computer Forensics
  • Network Intrusion Analysis
  • Incident Response
  • Data and Event Analysis
  • Incident Handling

210-250 dumps

QUESTION 1
Which technology supports the stateless assignment of IPv6 210-250 dumps addresses?
A. DNS
B. DHCPv6
C. DHCP
D. autoconfiguration
210-250 exam Correct Answer: BD
Explanation
QUESTION 2
What are two requirements for an HSRP group? (Choose two.)
A. exactly one active router
B. one or more standby routers
C. one or more backup virtual routers
D. exactly one standby active router
E. exactly one backup virtual router
Correct Answer: AB
Explanation
QUESTION 3
After you configure the Loopback0 interface, which command can you enter to verify the status of the
interface and determine whether fast switching is enabled?
A. Router#show ip interface loopback 0
B. Router#show run
C. Router#show interface loopback 0
D. Router#show ip interface brief
210-250 exam Correct Answer: A
Explanation
QUESTION 4
Which command sequence can you enter to create VLAN 20 and assign it to an interface on a switch?
A. Switch(config)#vlan 20
Switch(config)#Interface gig x/y
Switch(config-if)#switchport access vlan 20
B. Switch(config)#Interface gig x/y
Switch(config-if)#vlan 20
Switch(config-vlan)#switchport access vlan 20
C. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport trunk native vlan 20
D. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport access vlan 20
E. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport trunk allowed vlan 20
Exam A
Correct Answer: A
Explanation
QUESTION 5
Which three commands can you use to set a router boot image? (Choose three.)
A. Router(config)# boot system flash c4500-p-mz.121-20.bin
B. Router(config)# boot system tftp c7300-js-mz.122-33.SB8a.bin
C. Router(config)#boot system rom c7301-advipservicesk9-mz.124-24.T4.bin
D. Router> boot flash:c180x-adventerprisek9-mz-124-6T.bin
E. Router(config)#boot flash:c180x-adventerprisek9-mz-124-6T.bin
F. Router(config)#boot bootldr bootflash:c4500-jk9s-mz.122-23f.bin
210-250 pdf Correct Answer: ABC
Explanation
QUESTION 6
Which two statements about IPv6 and routing protocols are true? (Choose two.)
A. Link-local addresses are used to form routing adjacencies.
B. OSPFv3 was developed to support IPv6 routing.
C. EIGRP, OSPF, and BGP are the only routing protocols that support IPv6.
D. Loopback addresses are used to form routing adjacencies.
E. EIGRPv3 was developed to support IPv6 routing.
Correct Answer: AB
Explanation
QUESTION 7
If primary and secondary root switches with priority 16384 both experience catastrophic losses, which
tertiary switch can take over?
A. a switch with priority 20480
B. a switch with priority 8192
C. a switch with priority 4096
D. a switch with priority 12288
210-250 vce Correct Answer: A
Explanation
QUESTION 8
Which two statements about late collisions are true? (Choose two.)
A. They may indicate a duplex mismatch.
B. By definition, they occur after the 512th bit of the frame has been transmitted.
C. They indicate received frames that did not pass the FCS match.
D. They are frames that exceed 1518 bytes.
E. They occur when CRC errors and interference occur on the cable.
Correct Answer: AB
Explanation
QUESTION 9
Which command can you enter to set the default route for all traffic to an interface?
A. router(config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1
B. router(config)#ip route 0.0.0.0 255.255.255.255 GigabitEthernet0/1
C. router(config-router)#default-information originate
D. router(config-router)#default-information originate always
210-250 exam Correct Answer: A
Explanation
QUESTION 10
Which two spanning-tree port states does RSTP combine to allow faster 210-250 dumps convergence? (Choose two.)
A. blocking
B. listening
C. learning
D. forwarding
E. discarding
Correct Answer: AB
Explanation
QUESTION 11
If a router has four interfaces and each interface is connected to four switches, how many broadcast
domains are present on the router?
A. 1
B. 2
C. 4
D. 8
Correct Answer: C
Explanation
QUESTION 12
Which command enables IPv6 forwarding on a Cisco router?
A. ipv6 local
B. ipv6 host
C. ipv6 unicast-routing
D. ipv6 neighbor
210-250 pdf Correct Answer: C
Explanation
QUESTION 13
Refer to the exhibit. What is the most appropriate summarization for these routes?

A. 10.0.0.0 /21
B. 10.0.0.0 /22
C. 10.0.0.0 /23
D. 10.0.0.0 /24
Correct Answer: B
Explanation
QUESTION 14
Which set of commands is recommended to prevent the use of a hub in the access layer?
A. switch(config-if)#switchport mode trunk
switch(config-if)#switchport port-security maximum 1
B. switch(config-if)#switchport mode trunk
switch(config-if)#switchport port-security mac-address 1
C. switch(config-if)#switchport mode access
switch(config-if)#switchport port-security maximum 1
D. switch(config-if)#switchport mode access
switch(config-if)#switchport port-security mac-address 1
210-250 vce Correct Answer: C
Explanation
QUESTION 15
A router has learned three possible routes that could be used to reach a destination network. One route is
from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782.
The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing
table?
A. the OSPF route
B. the EIGRP route
C. the RIPv2 route
D. all three routes
E. the OSPF and RIPv2 routes
Correct Answer: B
Explanation
QUESTION 16
Two routers named Atlanta and Brevard are connected via their serial interfaces as illustrated, but they are
unable to communicate. The Atlanta router is known to have the correct configuration.

Given the partial configurations, identify the fault on the Brevard router that is causing the lack of
connectivity
A. incompatible IP address
B. insufficient bandwidth
C. incorrect subnet mask
D. incompatible encapsulation
E. link reliability too low
F. IPCP closed
210-250 exam Correct Answer: D
Explanation
QUESTION 17
A network administrator needs to configure a serial link between the main office and a remote location. The
router at the remote office is a non-Cisco router. How should the network administrator configure the serial
interface of the main office router to make the connection?
A. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252
Main(config-if)# no shut
B. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252
Main(config-if)# encapsulation ppp
Main(config-if)# no shut
C. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252
Main(config-if)# encapsulation frame-relay
Main(config-if)# authentication chap
Main(config-if)# no shut
D. Main(config)# interface serial 0/0
Main(config-if)#ip address 172.16.1.1 255.255.255.252
Main(config-if)#encapsulation ietf
Main(config-if)# no shut
Correct Answer: B
Explanation
QUESTION 18
Which Layer 2 protocol encapsulation type supports synchronous and asynchronous circuits and has built
in security mechanisms? 210-250 dumps Given the partial configurations, identify the fault on the Brevard router that is causing the lack of
connectivity
A. incompatible IP address
B. insufficient bandwidth
C. incorrect subnet mask
D. incompatible encapsulation
E. link reliability too low
F. IPCP closed
Correct Answer: D
Explanation
QUESTION 19
Refer to the exhibit. The two connected ports on the switch are not turning orange or green. What would be
the most effective steps to troubleshoot this physical layer problem? (Choose three.)

A. Ensure that the Ethernet encapsulations match on the interconnected router and switch ports.
B. Ensure that cables A and B are straight-through cables.
C. Ensure cable A is plugged into a trunk port.
D. Ensure the switch has power.
E. Reboot all of the devices.
F. Reseat all cables.
Correct Answer: BDF
Explanation
QUESTION 20
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers
cannot establish an adjacency relationship on their common Ethernet link.

The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on
the information in the graphic, what is the cause of this problem?
A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.
210-250 pdf Correct Answer: D
Explanation
QUESTION 21
What will happen if a private IP address is assigned to a public interface connected to an ISP?
A. Addresses in a private range will be not be routed on the Internet backbone.
B. Only the ISP router will have the capability to access the public network.
C. The NAT process will be used to translate this address to a valid IP address.
D. A conflict of IP addresses happens, because other public routers can use the same range.
Correct Answer: A
Explanation

The Cisco 210-250 dumps are designed to ensure optimum performance. So, with these practice tests, you will not waste precious studying hours filling your head with useless information. Furthermore, the various tools help learners of every speed and style to practice the Cisco https://www.pass4itsure.com/210-250.html dumps information.